福州華美批發直銷橡塑保溫管 吸音橡塑海綿管施工方案

橡塑保溫材料與其他保溫材料的泡孔結構比：

Rubber and plastic heat preservation material and other insulation foam pore structure than:

1、玻璃纖維：開孔結構水汽滲透率*（濕阻因子為3-5），導致隨使用時間延長導熱系數升高，使保溫效果大大降低。

1, glass fibre: open pore structure high water vapor permeability (wet resistance factor for 3 to 5), result in higher with the extension of use time coefficient of thermal conductivity, the heat preservation effect is reduced greatly.

2、發泡聚乙烯：連孔結構，添加阻燃劑后有較高的水汽滲透率（濕阻因子為1000），其材質硬而發脆，易破損，壽命短。

2, foaming polyethylene: even the pore structure, adding flame retardant has a high water vapor permeability (wet resistance factor of 1000), the material of hard and brittle, easy damage, short service life.

3、橡塑保溫材料：閉孔結構有極小的水汽滲透率（濕阻因子為10000以上）能長期保持較低的導熱系數。

3, rubber and plastic heat preservation material: obturator structure with minimal water vapor permeability (wet resistance factor of 10000 or above) to maintain low coefficient of thermal conductivity for a long time.

采暖、空調管道保溫材料性能比較表

Heating, air conditioning pipe heat preservation material performance comparison table

材料名稱 密度 導熱系數 溫度 經濟指標

The name of the material Density coefficient of thermal conductivity temperature indicators

水泥珍珠巖管 250-400 0.058-0.087 <600 不適用

Cement perlite tube 250-400-0.058-0.087 < 600 shall not apply

巖棉保溫管 100-200 0.082-0.058 -268-350 綜合成本高

Rock wool insulating tubes, 100-200-0.082-0.058-268-350 comprehensive cost is high

硅酸鋁纖維管 300-380 0.047-0.058 ≤1000 價格較高

Aluminum silicate fiber, 300-380-0.047-0.058 or less 1000 price is higher

聚苯乙烯塑料管20-50 0.031-0.047 -80-70 價格適中

Polystyrene plastic pipe 20 to 50 moderate price 0.031-0.047-80-80

聚氨酯預制保溫管 30-42 0.023 50-160 成本高

Prefabricated polyurethane insulation pipe 30-50-160 0.023 42 cost is high

橡塑絕熱保溫管 50-60 0.032 -50-110 價格相對低廉

Rubber insulation pipe 50 to 60 0.032-50-110 price is relatively cheap

水泥珍珠巖，巖棉，聚苯乙烯塑料

Cement perlite, rock wool, polystyrene plastics

福州華美批發直銷橡塑保溫管 吸音橡塑海綿管施工方案

橡塑保溫管生產廠家在產品的運輸過程中總會遇到這樣那樣的問題，那能否對這些問題進行正確的分析，并提出解決方案就顯得尤為重要了。下面小編就來給您科普一下。

Rubber insulation pipe manufacturers in the process of the transportation of products will always meet this or that kind of problem, is that the correct analysis of these problems, and puts forward solution is particularly important. Below small make up just to give you the popular science.

    橡塑保溫管能夠減少取暖能源消耗，是新一代的節能保溫材料。上世紀70年代，不少國家已經開始重視建筑節能，橡塑保溫管開始走向市場，有效的減少了取暖保溫消耗的能源。

Rubber insulation pipe can reduce heating energy consumption, is the new generation of energy-saving insulation materials. In the 1970 s, many countries have begun to attach importance to building energy efficiency, rubber insulation pipe began to market, reduce the heating heat consumption of energy.

橡塑材料

Rubber and plastic materials

廊坊福佳斯新型保溫建材有限公司

Langfang at the new thermal insulation building materials co., LTD.

：

sales hotline:

三、施工要求：

Three, construction requirements:

橡塑絕熱保溫材料的安裝應注意以下幾點：

Rubber insulation material the installation should pay attention to the following:

3.1、 所有的割隙、接頭都需用膠水粘接密封。

3.1, all cutting gap, joint needs special glue adhesive seal.

3.2、 安裝后所有的三通、彎頭、閥門、法蘭和其他附件都需達到設計厚度。

3.2 after install, all the three links, elbow, valve, flange and other accessories are required to meet the design thickness.

3.3、 膠水粘結時不要太用力，所有材料間的接口應在輕微擠壓下粘合。

3.3, don't too hard, glue bonding interface between all the materials should be under mild extruding glue.

3.4、 安裝時應先大管后小管，先彎頭、三通后直管，zui后閥門、法蘭。

After 3.4, when installation should first fill small tube, elbow, tee before straight pipe, valve, flange in the end.

3.5、 當安裝冷凍水管和制冷設備時，橡塑管材的兩端和鐵管之間的空隙都需涂上膠水粘結起來，粘接寬度應不等于橡塑材料厚度。

3.5, when installing a chilled water and cooling equipment, rubber and plastic will be the gap between the ends of the pipe and pipe coated with glue adhesive, adhesive width should be no is equal to the thickness of rubber and plastic materials.

3.6、 管道的割隙口應盡量安裝在不顯眼處，且兩條管材的割隙口應相互錯開。

3.6, pipe cutting gap, should be installed in an inconspicuous area and two pipe cutting gap should be staggered.

3.7、 機器在使用中不要安裝。裝好后36小時內切勿開機。

Do not install in 3.7, machines in use. Do not boot loaded after 36 hours.

3.8、 大管徑橡塑管由于包裝關系已變成橢圓形，剖開時請剖較扁平的那邊。

3.8, large diameter rubber tube due to relationship has become oval packing, please split the flat side when they cut it open.